Searching for the best 3d printer controller? We totally understand you.
We at ReviewCity.club realize that choosing a 3d printer controller is a hard task.
Therefore, our mission is to help you get the best product by gathering information, testing, and writing our reviews.
With the help of our detailed analysis, here you will see the top 3d printer controller.
Our best pick is KINGPRINT TMC2208 V3.0-UART with SKR V1.3 32bit Smoothieware Controller Panel Board for 3D Printer Compatible With12864LCD/Support A4988/8825/TMC2208/TMC2100 Drivers. However, all of the items on our list are of great quality.
Look at the price table we made for you and continue reading to see what we found out when we checked the top 10 3d printer controller.
Best 3d printer controller Reviewed
Continue to read to see the comprehensive reviews.
BIGTREETECH 3D Printer Part SKR V1.4 Turbo 32bit Control Board Smoothieboard&Marlin Open Source SKR V1.4 SKR V1.3 Upgrade Support TMC2209/TMC2208/TMC2130 Drivers (SKR V1.4 Turbo)
- 【32 Bit High Performance Microprocessor】SKR V.4 Turbo silent board adopts 32 bit ARM level Cortex-M3 series LPC1769,120MHz frequency m icroprocessor, which can reduce the stepper motor noise greatly, a choice to be your 3D printer controller.
- 【Multiple Function】 SKR V1.4 Turbo motherboard supports resume printing while power Of,filament break detection and automatic shutdown after printing function.In the meanwhile,it can Support TFT2.4, TFT70, TFT3.5 inch colorful touch screen and 2004LCD,12864LCD screen.
- 【Compatible with Multi-Stepper Motor Drivers 】 On-board TMC driver SPI operating mode and UART operating mode ,Support stepper driver TMC5161, TMC5160, TMC2209, TMC2225, TMC2208,TMC2130, ST820, LV8729, DRV8825, A4988, etc.
- 【 Easy and Simple to Flash Firmware】Firstly download firmware of SKR V1.4 motherboard,copy and save it to SD card.firmware must bed reserved ,then re-plug the SD card and wait to 10s.The firmware has been successfully updated when the progress bar and interface appear.
- 【Reserve BLTouch interfaces 】 Reserve BLTouch interfaces SERVOS and Probe for easy to connect with BLTouch.
BIGTREETECH TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
- 1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
- 2.Serial port screen mode supports two printing modes: SD card and U disk.
- 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
- 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);
- 5.2 sets of UART serial port extension ports are reserved for DIY use.
BIQU LCD 12864 Version Graphic Smart Display Controller Module with Adapter and Cable for RAMPS 1.4 Reprap 3D Printer Kit
- A LCD display module with blue backlight, small and light appearance, suitbale for copiers, fax machines, laser printers, industrial test equipment, networking
- Small and light appearance, it is easy and convenient to use
- Suitable for copiers, fax machines, laser printers, industrial test equipment, networking equipment etc
- LCD control panel through which you can achieve spooling is the 3D model Gcode files are copied to the SD card, and then print the file via the LCD control panel
- This version is an upgraded version of reprap smart controller
KINGPRINT TMC2208 V3.0-UART with SKR V1.3 32bit Smoothieware Controller Panel Board for 3D Printer Compatible With12864LCD/Support A4988/8825/TMC2208/TMC2100 Drivers
- 1.The performance of the ARM-class Cortex-M3 series LPC1768 main control chip with 32-bit frequency and 100MHz is greatly improved;Reserve the extended port SERVOS of the PWM signal to support BL Touch
- 2.Support Resume Printing While Power Off,Filament Break,CE Certification to adopt 4-Layer PCB with “Gold deposition technology” which capability is more stable and better heat dissipation
- 3..Onboard TMC2130 driven SPI mode of operation and TMC2208 driven UART mode,The utility model eliminates the complicated wiring process and can be used only by simply plugging and unplugging the jumper cap;
- 4.The high-performance MOSFET tube has better heat dissipation effect; it supports functions such as power-off continuous shooting, material cut detection, and shutdown;
- 5.Use the power selection design ,to separate the USB power supply from the switching power supply, effectively avoiding short circuits,Causes the computer's USB port to be burned;
BIGTREETECH SKR Pro v1.2 32-bit Motherboard high-Frequency 3D Printer Control Board, Support TMC5160, TMC2208, TMC2130, TFT28, TFT32, TFT35, 12864LCD ect.
- The main control uses the ARM-level Cortex-M4 series with a 32-bit dominant frequency of 168 MHz STM32F407ZGT6 chip, performance is greatly improved.
- Equipped with highly modular open source firmware Marlin2.0, it is convenient for users to DIY and further-development, to avoid the worry of not being able to master the core code.
- Motor driver support :TMC5160,TMC2208,TMC2130,ST820,LV8729, DRV8825,A4988, etc.Display screen support: BIGTREETECH- 2.8 inch TFT,BIGTREETECH-3.5 inch TFT, LCD2004,LCD12864.
- Support Serial WIFI Online Printing. 6 motor drives, 3 extruders, 3 CNC fans. Reserve extended ports of BL Touch, PWM, ADC, UART, I2C and SPI;Support power-off continuous printing, material cut detection, shutdown and other functions;Support for dual Z axis printers (series dual Z.
BIGTREETECH TFT24 V1.1 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
- BIGTREETECH TFT24-V1.1 is a small volume ultra-clear 3D printer display board. It can work in two modes.
- ARM Cortex-M3 series STM32F105RCT6 chip with 32-bit CPU 72MHz;
- Upgrade the firmware by SD card. It is easy and convenient to operate.Serial port screen mode supports two printing modes: SD card and U disk
- This display board has higher compatibility. Users can select two work modes, they are UART serial port screen mode and 12864 screen mode.
BIQU MKS-Base V1.6 Plate Controller Board for 3D Printer Ramps 1.4
- Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware
- Firmware can use the same configuration as ramps1.4
- Easy DISPLAY + SD-CARD connector,RepRapDiscount SmartController compatible pin header on board
- Easy connect MKS TFT on AUX-1
- 3x temperature ADC connectors for thermistors
BIQU Smart Display Controller Ramps 1.4 2004LCD Controller with Adapter for 3D Printer RepRap Adapter
- Popular RepRap 3D Printer LCD Controller and SD Card Reader
- The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display
- You can easily connect it to your RAMPS 1.4 board using "smart adapter" included
- 3D design print without a computer, just use the G code design stored on the SD card
- With Smart LCD Controller you can print 3D designs without USB connection to your computer
HiLetgo 3D Printer Reprap Smart Controller 12864 LCD Display with Smart Controller Board for 3D Printer RAMPS 1.4 Reprap Mendel Prusa for Arduino 128x64 LCD Blue Color
BIGTREETECH SKR Mini E3 V2.0 Control Board 32Bit New Upgrade for Creality Ender 3, with TFT35 E3 V3.0 Graphic Smart Display Controller Board 3D Printer Parts
- 【TFT35 E3 V3.0】 ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz; Upgrade the firmware by SD card. It is easy and convenient to operate.
- 【SKR Mini E3 V2.0】 ARM Cortex-M3 Series STM32F103RCT6 Master Controller with 32-bit Main Frequency of 72MHz Chip;Integrate UART mode of TMC2209 to simplify debugging of motherboard and driver.Reserve expansion ports for TMC2209 pins to facilitate users to use DIAG instead of Endstop.
- 【TFT35 E3 V3.0】 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk.
- 【TFT35 E3 V3.0】 LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.)
- 【SKR Mini E3 V2.0 Firmware】 https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V2.0 ；【TFT35 E3 V3.0 Firmware】 https://github.com/bigtreetech/BTT-TFT35-E3-V3.0.
With this, our list of best 3d printer controller has come to an end. If we didn’t manage to assist you with the process of choosing the right thing for your needs, e-mail us.